09
IC FABRICATION FLOWInspection & Metrology
STEP 09 OF 09 — PROCESS CONTROL
Inspection &
Metrology
Inspection และ Metrology คือ "ตาของ fab" — วัด CD, Overlay, Film Thickness, ตรวจจับ Defect ในทุกขั้นตอนเพื่อควบคุม Yield และ Process เป็นสิ่งที่แยกจาก fab ไม่ได้
01 Inspection vs. Metrology — ต่างกันอย่างไร
INSPECTION
ค้นหา Defect
ตรวจหาสิ่งผิดปกติ: particle, scratch, bridge, void — ตอบ "มี defect ไหม" และ "อยู่ที่ไหน"
METROLOGY
วัดค่า Parameter
วัดค่าที่แน่นอน: CD, overlay, thickness, roughness — ตอบ "ค่าคือเท่าไร" และ "อยู่ใน spec ไหม"
ใน Advanced Fab — Metrology คือ 20% ของ Equipment
ใน TSMC หรือ Intel fab ที่ 2–3nm มี metrology tool หลายร้อยเครื่อง ทุก wafer ถูกวัด inline หลายจุดต่อ layer — ข้อมูลทั้งหมด feed ไป Advanced Process Control (APC) ระบบ
📍 CAREER ROADMAP CONTEXT
STAGE 05 — CMP & METROLOGY: Planarization & Inline Measurement
CMP (oxide, metal, STI planarization) — slurry chemistry, dishing, erosion; metrology: AFM, SEM cross-section, TEM, XRD, ellipsometry, CD-SEM; SPC control charts; defect inspection (KLA brightfield/darkfield)
Equipment: Applied Materials Reflexion CMP, KLA-Tencor inspection, FEI TEM
Path: Process / Fab Engineer
CMP (oxide, metal, STI planarization) — slurry chemistry, dishing, erosion; metrology: AFM, SEM cross-section, TEM, XRD, ellipsometry, CD-SEM; SPC control charts; defect inspection (KLA brightfield/darkfield)
Equipment: Applied Materials Reflexion CMP, KLA-Tencor inspection, FEI TEM
Path: Process / Fab Engineer
02 Optical Inspection & Metrology
1
Ellipsometry
วัด film thickness และ optical constants (n, k) จากการ polarization ของแสง — ความแม่นยำ ±0.01 nm ใช้วัด gate oxide, SiN, ARC, PR thickness
2
Optical CD (OCD / Scatterometry)
ยิงแสงที่ grating pattern แล้ว model diffraction spectrum → extract CD, SWA (sidewall angle), height, pitch — ไม่ destructive และ fast throughput
3
Brightfield / Darkfield Inspection
Brightfield: ใช้แสงสะท้อนตรง ตรวจ defect บน wafer surface แบบ die-to-die compare | Darkfield: แสงเฉียง sensitivity สูงสำหรับ particle เล็กมาก
4
Reflectometry & XRF
Reflectometry: thickness measurement แบบ single wavelength | X-Ray Fluorescence (XRF): วัด metal layer thickness และ composition เช่น Cu, W, TiN
ELLIPSOMETRY — MEASURED ANGLES
tan(Ψ)·exp(i·Δ) = rp / rs
Ψ = amplitude ratio | Δ = phase difference | rp, rs = Fresnel reflection coefficients — fit กับ model เพื่อหา n, k, thickness
03 SEM, TEM และ Electron Beam Methods
| Method | Resolution | Sample Prep | การใช้งาน |
|---|---|---|---|
| CD-SEM | 1–3 nm | ไม่ต้อง (inline) | Critical Dimension หลัง litho/etch |
| FE-SEM | <2 nm | ไม่ต้อง | Defect review, morphology |
| TEM (cross-section) | <0.1 nm | FIB cut (destructive) | Gate oxide thickness, interface quality |
| STEM-EDS | ~0.2 nm | FIB cut | Elemental mapping ของ device structure |
| e-Beam Inspection | sub-nm | ไม่ต้อง | Electrical defect ที่ optical ไม่เห็น (EBDI) |
CD-SEM — Workhorse ของ Fab
ทุก lithography layer ต้องวัด CD ด้วย CD-SEM อย่างน้อย 5 point ต่อ wafer และ sampling ทุกๆ N wafers — ผลที่ได้ feed ไป APC เพื่อ adjust exposure dose/focus ใน stepper step ถัดไป
04 Overlay และ CD Measurement
Overlay คือการวัดว่า pattern ชั้นใหม่ align ตรงกับชั้นก่อนหน้าแค่ไหน — requirement ที่ 3nm node อยู่ที่ <1 nm overlay error
AIM Target
Advanced Imaging Metrology
Diffracting grating target เล็กกว่า box-in-box วัดได้แม่นกว่า ใช้ใน EUV layer
µDBO
Diffraction-Based Overlay
วัด overlay จาก +1/-1 diffraction order ไม่ต้องมองเห็น pattern โดยตรง
e-Beam OVL
Electron Beam Overlay
Accuracy สูงกว่า optical สำหรับ sub-2nm node แต่ throughput ต่ำกว่า
APC Feed-forward
Overlay Correction
วัด overlay → ส่งค่า correction ไป scanner ทันทีสำหรับ wafer ถัดไป
05 Defect Management & Yield
Defect density มีผลโดยตรงต่อ yield — การจัดการ defect เป็นงาน continuous ที่ทำตลอด process flow
POISSON YIELD MODEL
Y = exp(−A × D₀)
Y = Yield | A = Die Area (cm²) | D₀ = Defect Density (defects/cm²) — ยิ่ง die ใหญ่หรือ defect เยอะ yield ตก
1
Inline Inspection (After Every Key Layer)
Scan wafer ด้วย brightfield/darkfield หลังทุก critical layer → detect killer defect ก่อนที่จะ process ต่อ ประหยัดค่า processing
2
Defect Review (DR-SEM)
ดู defect ที่ detect ได้ด้วย SEM เพื่อ classify: particle, scratch, bridge, void, pit — แต่ละ type มีที่มาต่างกัน
3
Defect Pareto & Root Cause
จัด Pareto ของ defect type → หา root cause → แก้ไข process (เปลี่ยน chemical, ทำความสะอาด chamber, adjust recipe)
4
Yield Learning Loop
Electrical test ← Defect map correlation ← เพื่อหาว่า defect ชนิดใดเป็น killer จริง → focus resource ที่ right defect type
| Defect Type | สาเหตุทั่วไป | วิธี Detect | Impact |
|---|---|---|---|
| Particle | Chamber, เสื้อผ้า, ท่อส่งก๊าซ | Darkfield scan | Short / open circuit |
| Bridge (Short) | Over-expose, under-etch | CD-SEM, e-beam | Yield killer |
| Open | Under-expose, over-etch, CMP erosion | e-beam, electrical | Yield killer |
| Void (in metal) | Cu ECP issue, CMP scratch | TEM cross-section | Reliability |
| Scratch | CMP, wafer handling | Brightfield scan | ขึ้นกับ location |
EUV Stochastic Defects — ความท้าทายใหม่
EUV lithography มี photon shot noise สูงกว่า DUV → เกิด stochastic defect แบบสุ่ม: micro-bridge, local CD variation — detect ยากมากด้วย conventional inspection ต้องใช้ e-beam sampling สูง หรือ actinic inspection (EUV light source) ซึ่ง cost สูงมาก